A window submittal does not fail because the window is bad. It fails because the package around the window is incomplete — a missing seal, a mismatched model suffix, an expiring NOA nobody checked. Every one of those is knowable before you send it.
Here is the full checklist, in the order the reviewer reads it.

The short version
The package has four parts, and they are not optional in High-Velocity Hurricane Zone counties:
- Product approval — a current Miami-Dade NOA in Miami-Dade (an FL# alone does not cover HVHZ) or a Florida Product Approval for Broward.
- Shop drawings — the window system, detailed and matching the approved product.
- Structural calculations — design pressures from the structural drawings, sealed by the engineer.
- Installation details — rough opening, supporting framework, method of attachment, waterproofing.
Miss any one, and the reviewer has a reason to bounce it. Let us go through each.
Product approval: the document that stops the permit
In Miami-Dade, the accepted product document is a Notice of Acceptance (NOA) issued by the county. Broward is also in the HVHZ, and accepts a Florida Product Approval that explicitly covers HVHZ use. If you are not sure which path applies to a job, the difference between a Miami-Dade NOA and a Florida Product Approval is the first thing to resolve.
Three checks on the approval before it goes into the package:
- It is current. An NOA carries an expiration date. A permit will not be issued against an expired NOA. Verify it on the issuing portal, not from a supplier PDF — this is how you check an approval is still valid.
- The model matches exactly. Not the product family — the exact model series, frame material, glass configuration, and anchor pattern. A “550” when the approval says “550T” is a rejection.
- The approval came with the right pages. The NOA generically consists of the cover sheet, the specific system pages, and the limitations/installation-detail pages. Shade-systems, excluded pages, and manufacturer brochures in place of the actual approval PDF are the single most common reason a package comes back.
- The right rows are marked. Highlight the applicable sizes, the model series, and the expiration date. A Florida Product Approval is online-only — print the floridabuilding.org result page with the series highlighted. A Miami-Dade NOA is a self-contained PDF, so the highlight goes on the PDF itself.
For a window, that product test behind the approval is the TAS series — large and small missile impact, uniform static air pressure, and cyclic wind loading under the TAS 201 / 202 / 203 protocols. The rating has to cover the pressure your project demands at that specific opening.
Shop drawings and structural calculations
Under the Florida Building Code, the architect or engineer of record must specify the design wind pressure — determined in accordance with FBC Chapter 16 — for every garage door, skylight, operative window, and fixed glazing (FBC §2411.3.1.4). That pressure appears on the structural drawings, and the manufacturer sizes its assembly against it.
The reviewer does not take your word for it. The governing FBC provision on shop drawings, FBC §2411.3.1.6, requires the drawings submitted for permit to detail rough opening dimensions, supporting framework, method of attachment, and waterproofing for all exterior doors, skylights, and windows. A manufacturer’s specialty engineer can prepare those details, provided they are admitted at permit time, completely identify the assembly, and bear the signature and seal of a professional engineer approved by the engineer of record.
So the package needs:
- A frontal elevation of each exterior wall — every opening’s location, size, and approval number, with the positive/negative design pressure. Required even on a straightforward residential replacement; missing it is a bounce.
- A window/door schedule tying each opening to its product and its design pressure.
- Shop drawings signed and sealed, matching the product in the approval.
- Structural calculations, in Miami-Dade grouped as a single PDF with a signed and sealed cover/index page.
The reviewer compares the negative and positive design pressure at that opening against the product’s approval rating — not a round number off a marketing sheet.
Anchors: reference the approval until you deviate
For a like-for-like replacement you do not redraw every anchor in section. The tested NOA/FPA already carries the anchor type, spacing, embedment, and edge distances for the substrate; attaching the approval and cross-referencing it is what the reviewer asks for. Mark the exact table option — substrate, anchor, spacing — you are using, and put the NOA/FPA number next to each opening.
One line on the plans covers the obligation:
All windows and doors shall be installed strictly in accordance with the attached NOA/FPA, including specified anchor type, embedment, edge distances, and spacing for the actual substrate.
You cross into drawn details — signed, sealed anchor and edge-distance drawings with calculations — the moment you step off the approval: different anchors, a different substrate, changed edge distances or spacings, or site-specific engineering instead of the NOA tables. Different anchors than the approval voids it, and the engineer’s detail becomes the controlling document.
The same trigger decides the seal. A straightforward replacement in an existing opening with no deviation does not need a fresh engineering seal — the approval carries it. New openings, block-ups, changed sizes, or any deviation do.
What reviewers bounce most often
These are the mismatches, not missing-paperwork cases, that stall a package past first review:
- Expired or superseded approval. The product was approved; the version on file is not the version that covers the job. Cheapest and most common.
- Approval and drawings disagree. Frame material, glass type, or anchor spacing in the drawings does not match the approved configuration. Approval for a similar product does not carry over to a different assembly.
- Seal or signature missing. Shop drawings and calculations in Miami-Dade carry a delegated engineer’s seal and the engineer of record’s approval stamp. An unsigned calculations cover page is a hard stop.
- Manufacturer name mismatch. The applicant’s legal name differs from the name on the NOA. A distributor selling under its own name needs a private-labeler or distributor agreement plus a re-stamped drawing set.
Build a register, not a folder
None of this is hard on a single opening. It compounds because a mid-size envelope package has dozens of openings, several product families, and every supplier substitution restarts the check. That is where a live register pays: product, approval number, expiration date, covered pressure range, model suffix. Reading a Miami-Dade NOA field by field is the pattern to build that register on.
If you are moving product by pulling PDFs from a folder each cycle, the failure modes above will keep finding you. A structured compliance workflow — where the approval register and the package assembly are the deliverable, not a scramble — is exactly what we build at EnergyCheck. See what a compliance-included estimating process looks like and whether the points pricing fits how you bid.
This is how approval paths work in Florida, not a guarantee any specific package will pass — the reviewer is the final word. Assemble the four parts above, checks in hand, and you have done everything the code and the county reasonably expect before you submit.